Open your drill-bit drawer and look at it honestly: every blunt bit in there is not scrap — it is a drill bit you already paid for, sitting there pretending to be dead.
A dull bit does not need replacing. It needs about a minute on a grinder and a shower of sparks, and the very next hole proves it — clean spirals instead of dust, no squeal, no smoke, no wrestling.
Three ways to do it follow — free, cheap, and push-button — and by the end you will know exactly which bits deserve a second life and which ones belong in the bin.
Quick Answer: Yes — you can sharpen drill bits at home with a bench grinder, a dedicated bit sharpener, or a file. Match the original 118° point angle and keep both cutting edges equal length; an uneven edge makes the bit wander and overheat.

Project at a glance: Time: 20–40 minutes first try (≤1 minute per bit once practiced) · Cost: $0 with a bench grinder you own, up to ~$150 for a dedicated sharpener · Skill level: beginner with a jig or sharpener, intermediate freehand.
Safety first: Grinding throws sparks and hot metal — wear eye protection and gloves. Bits get HOT during sharpening; quench in water frequently and never grab a freshly ground bit barehanded. And secure the grinder — a bench grinder that walks across the bench is a hazard.
Know when to sharpen vs replace
Sharpen it: the bit is dull (slow cutting, burning, squealing) but the flutes and shank are intact. Standard twist bits, brad-point bits, and quality bits of all kinds.
Replace it: the bit is chipped badly, the flutes are damaged, it’s bent, it’s a cheap $2 bit (your time is worth more), or it’s a specialized bit (hole saws, Forstner bits need professional sharpening or replacement — here’s the blade replacement guide for the same logic applied to saw blades).
The economics: if a bit costs $3, sharpening rarely pays — buy new. If it costs $15+, sharpening is absolutely worth learning. Most DIYers’ bit collections fall in the “worth sharpening” range once you count how many go dull per year.
Understanding what you’re recreating
A twist drill bit’s cutting happens at two angled faces meeting at the tip — the point angle (118° is standard for general purpose, 135° for harder materials) and the relief angle behind each cutting edge. When you sharpen, you’re recreating these two edges symmetrically.
Symmetry is everything. If one cutting edge is longer or angled differently than the other, the bit drills oversized, wandering holes. This is why freehand sharpening takes practice — and why jigs and sharpeners exist.
Bookmark This Checklist — Tools & Materials for Sharpening Drill Bits
- Dull twist drill bits (practice on cheap ones first — the skill is free, the bits aren’t)
- Bench grinder with a 6 in / 150 mm or 8 in / 200 mm wheel (any one you already own works)
- Safety glasses + work gloves — grinding throws sparks and hot metal chips
- A cup of water for quenching — dip the bit every few seconds while grinding
- Wheel dressing stone (optional but recommended) — a flat, clean wheel face grinds a true edge
- Marker (optional) — mark the flute to track equal passes on each side

Keep This Chart Handy — Point Angles by Material
Sharpening is recreating two angled faces at the tip: the point angle and the relief angle behind each cutting edge. Get the angle right for the material and the bit cuts cleanly; get it wrong and it wanders, squeals, and overheats.
| Material / job | Point angle | What to remember while grinding |
|---|---|---|
| General purpose and wood | 118° | The standard angle. On a bench grinder freehand, hold the bit at roughly 59° to the wheel face — half of the 118° point angle. |
| Harder materials and metal | 135° (with split point) | A split point creates a self-centering tip — excellent for metal. Grinding a 135° bit to 118° is not catastrophic, but matching the original is better. |
| Any bit, any angle | Match the original | Symmetry is everything: both cutting edges must be equal length and identically angled, or the bit drills oversized, wandering holes. Count your passes (for example, 3 per side, alternating). |
| Brad-point bits | Preserve the factory geometry | Use a fine wheel or diamond file, work gently, and keep the brad (center spur) and the two spurs intact. Fiddlier than twist bits — many people sharpen only the premium ones. |
| Carbide-tipped masonry bits | Light touch-up only | A diamond wheel or diamond file can touch them up, but carbide is brittle — aggressive grinding chips it. Heavy damage means replacement. |
The rule that protects every angle above: quench in water frequently — every few seconds. Blue discoloration means the temper is gone and the bit will never hold an edge again, no matter how perfect the angle.
Method 1: Bench grinder freehand (free, skill required)
The traditional method. Every old-timer learned this; it costs nothing and works brilliantly once you’ve practiced.
How:
1. Put on eye protection. Dress the grinding wheel if it’s grooved (a clean, flat wheel face matters).
2. Hold the bit at roughly 59° to the wheel face (half of the 118° point angle) — this is the angle you’re recreating.
3. Rest the bit on the tool rest, cutting edge facing up. Grind one flute, rotating the bit slightly downward as you go to create the relief angle behind the cutting edge.
4. Quench in water frequently — every few seconds. Overheating ruins the temper (blue discoloration = too hot = softened steel = a bit that’ll dull instantly).
5. Grind both flutes equally — count your passes (e.g., 3 passes per side, alternating) to keep them symmetric.
6. Test on scrap wood. It should cut clean spirals of waste, not dust.
Pros: free, fast once learned, works anywhere there’s a grinder.
Cons: real learning curve — your first 5–10 bits will be mediocre. Symmetry by eye takes practice.
Tip: practice on your cheapest, dullest bits first. Nobody’s first freehand sharpening is good; everybody’s twentieth is fine.
Method 2: Drill bit sharpening jig ($20–$40, easier)
A jig holds the bit at the correct angle against the grinder — you supply the motion, the jig supplies the geometry. Popular options clamp the bit and ride on the grinder’s tool rest, maintaining the point angle automatically.
How: mount the bit in the jig per its instructions, set it against the wheel, and work it back and forth. The jig controls the angle; you control the pressure and the quenching. Flip to do the second flute.
Pros: dramatically easier symmetry than freehand, cheap, works with your existing grinder.
Cons: setup takes a few minutes per bit size, quality varies by jig, still requires a bench grinder.
Best for: DIYers who want reliable results without the freehand learning curve and already own a grinder.
Method 3: Dedicated drill bit sharpener ($60–$150, easiest)
Machines like the Drill Doctor and its competitors: insert the bit, the machine aligns it, sharpens both flutes automatically with correct angles. Push-button simple.
How: chuck the bit in the machine’s holder, insert into the sharpening port, rotate per instructions. The machine handles angles and symmetry. Some models also split the point (creating a self-centering tip — excellent for metal).
Pros: foolproof results, fast, consistent, handles split points. Anyone can do it first try.
Cons: costs real money, limited to the bit sizes the machine accepts (check range before buying), slower per bit than a skilled freehand grinder.
Best for: anyone with lots of bits to maintain, or anyone who tried freehand and bounced off. If you burn through bits regularly, it pays for itself within a year.
Comparison: which method for you?
The right sharpening method depends on your tools and patience. Freehand on a bench grinder costs nothing and gives excellent results once practiced. A $20–$40 jig adds consistent angles for DIYers. A dedicated sharpener ($60–$150) is fastest and easiest — push a button, get a sharp bit every time.
| Freehand grinder | Sharpening jig | Dedicated sharpener | |
|---|---|---|---|
| Cost | $0 (have grinder) | $20–$40 | $60–$150 |
| Learning curve | Steep | Moderate | None |
| Result quality | Excellent (once skilled) | Good–excellent | Consistently good |
| Speed per bit | 1–2 min (skilled) | 3–5 min | 2–3 min |
| Best for | Old hands, many bits | DIYers with a grinder | Everyone else |
The mistakes that ruin bits
- Overheating (blue steel). The #1 killer. If the bit turns blue/straw-colored at the tip, you’ve softened the steel — it’ll never hold an edge again. Quench constantly. When in doubt, quench.
- Asymmetric grinding. Unequal flutes = oversized, wandering holes. Count passes, alternate sides, check symmetry visually.
- Wrong point angle. 118° for wood/general, 135° (with split point) for metal. Grinding a 135° bit to 118° isn’t catastrophic, but matching the original is better.
- Grinding the flutes, not the tip. The cutting happens at the tip’s two edges — grinding anywhere else just removes metal for no benefit.
- Sharpening a bit that’s actually damaged. Chipped flutes, bent shanks, cracked bits — sharpening can’t fix structural damage. Know when to let go.
How do I know if my bit is dull vs. just wrong for the material?
Dull: it used to cut well and gradually got worse; it squeals, smokes, or produces dust instead of shavings. Wrong bit: it never cut well in this material (e.g., wood bit in steel). If it worked before and doesn’t now, it’s dull — sharpen it.
Can I sharpen brad-point bits?
Yes, but carefully — the brad (center spur) and the two spurs need preservation. Use a fine wheel or diamond file, work gently, and maintain the spur geometry. It’s fiddlier than twist bits; many people just replace cheap brad-points and sharpen only the premium ones.
Can I sharpen masonry bits?
Carbide-tipped masonry bits can be touched up with a diamond wheel or diamond file, but the carbide is brittle — aggressive grinding chips it. Light touch-ups extend life; heavy damage means replacement.
How often should I sharpen?
When performance drops — there’s no schedule. Pros touch up bits constantly (a few seconds on the grinder between jobs); DIYers sharpen when they notice the decline. The sooner you sharpen a slightly-dull bit, the less metal you remove and the longer it lasts overall.
Is it worth sharpening $2 bits?
Honestly? No — your time is worth more. Sharpen bits that cost enough to matter ($8+), or use cheap bits as practice for learning freehand technique. Both are valid; just don’t spend 10 minutes resurrecting a $2 bit.
Why do my sharpened bits drill oversized holes?
Asymmetric flutes — one cutting edge is longer than the other, so the bit orbits instead of spinning true. This is the classic freehand beginner result. Focus on equal passes per side, and check the tip visually: both edges should look identical.
Keep This Chart Handy — Your Sharpened Bit Still Isn’t Right? Diagnose It
Ground the bit and the hole still looks wrong? Match the symptom to the row — every cause and fix below comes from this guide.
| Symptom | Likely cause | The fix |
|---|---|---|
| Still squeals, smokes, or makes dust instead of shavings | Still dull — the cutting edge is not fully recreated yet | Grind a few more passes, quenching in water every few seconds; test again on scrap wood (a sharp bit cuts clean spirals of waste, not dust) |
| Holes come out oversized | One cutting edge is longer than the other — asymmetric flutes make the bit orbit instead of spinning true | Count your passes and alternate sides (for example, 3 per side) so both edges stay equal; check the tip visually — both edges should look identical |
| Bit wanders or will not bite | Wrong point angle, or uneven edges | Match the original angle — 118° for wood and general purpose, 135° (with split point) for metal and harder materials |
| Tip turned blue or straw-coloured | Overheated — the steel lost its temper and will never hold an edge again | Stop grinding that bit; replace it. Quench constantly on the next one — when in doubt, quench |
| Bit chatters, wobbles, or snaps | Structural damage — chipped flutes, bent shank, or a crack | Sharpening cannot fix structural damage. Replace the bit — a weakened bit can snap mid-hole |
The verdict
Sharpening drill bits is one of those skills that seems intimidating until you’ve done it twice — then it becomes a 2-minute habit that saves real money and keeps your drilling frustration-free. Start with Method 2 or 3 if freehand feels daunting; graduate to freehand when you’re curious.
And remember the meta-lesson: a sharp cheap bit outperforms a dull expensive bit every time. Maintenance beats purchase price. The best bit in your collection isn’t the priciest one — it’s the sharpest one.
Sharpen or Replace? — Keep This Decision Chart Handy
Here’s the question nobody answers honestly: not every drill bit deserves a second life. Run your bit down this chart before you touch the grinder — some bits sharpen beautifully, others are money pits wearing a familiar shape.
| Bit condition | Verdict | Why |
|---|---|---|
| Just dull — no chips, no cracks, flutes intact | SHARPEN | A touch-up takes minutes and a sharp bit cuts faster and cooler than a dull one ever will. |
| Small nicks or slightly rounded cutting edges | SHARPEN | Grind back just past the damage, keep the original point angle, and it’s a working bit again. |
| Blue or straw discoloration along the flutes (overheated) | REPLACE | The steel lost its temper — that bit will never hold an edge again, no matter how pretty you grind it. |
| Cracked flute, bent shank, or a cutting lip chipped clean off | REPLACE | Structural damage doesn’t grind out. A weakened bit can snap mid-hole. |
| Snapped clean in two | REPLACE | For standard bits, a new one is the sane answer — save the grinder time for bits worth saving. |
| Worn below its stamped size after many sharpenings | REPLACE | Every sharpening trims a little; once it’s undersized, your “10 mm hole” comes out loose. |
Keep Reading
Liked this? Three more from Tool Worth Lab worth your time:
- How to Sharpen a Chainsaw Chain — the same “fix, don’t replace” logic, applied to your saw.
- Drill Bit Size for Concrete Anchor — pick the right bit size before you drill (bookmark the chart).
- How to Clean and Maintain Power Tools — the full care routine that keeps every tool — and every bit — cutting like new.
Tool Worth Lab provides research-based maintenance guidance. Always wear eye protection when grinding. Quench frequently — blue steel means the temper is gone and the bit won’t hold an edge.
For official specifications and support documentation, see DeWalt’s official site.
For official specifications, see Bosch’s official site.
